NANO Anti-Mould Paint, silicate based

Google+

Multifunctional silicate-based indoor coating with NANO active ingredients (NANO SILVER), chlorine-free active substances and insulating bubbles

 

NANO ANTI - MOULD Paint - Product characteristics NANO ANTI - MOULD Paint  - ready-to-use high-coverage organic wall paint with thermoinsulating pigments and a high pH. The finishes achieved are flat matt, opaque and non-flammable. The product contains no toxic active substances and creates coating that is particularly permeable to water vapour. The NANO particles (NANO SILVER) used are active throughout the life of the coating and guarantee that the coating has a long‑lasting effect. NANO ANTI - MOULD Paint can be used for both prevention and remediation. Coated walls are largely resistant to renewed fungal growth.

 

NANO ANTI - MOULD Paint - where to use
On mineral surfaces indoors, such as concrete, cement plaster, lime cement plaster, masonry, stucco, gypsum plaster, lime sand brick, natural stone and fibre cement board walls and ceilings. Also on intact coats of old lime, mineral or silicate paint. Suitable for woodchip wallpapers and emulsion painted surfaces (wet abrasion resistance class 1, 2, 3 DIN EN 13300).

NANO ANTI - MOULD Paint - Preparation
All surfaces should be clean, dry, sound, absorbent, free of separating agents and without cracks. Poorly adhering substrates or substrates that cannot be consolidated need to be removed completely. Areas affected by mould should be treated with a commercial mould remover, taking care to ensure dust‑free removal of the fungi.

NANO ANTI - MOULD Paint - Painting
1. NANO ANTI - MOULD Paint should always be stirred thoroughly before being applied. It can be applied undiluted or thinned with max. 5% water. The product can only be tinted with appropriate tinting concentrates for acrylic and silicate. Do not mix with other paints.
2.  NANO ANTI - MOULD Paint can be applied by roller, brush or spray gun. For airless spraying, a strainer should be placed in front of the intake.
3.  Surfaces that are not to be coated, especially glass or aluminium, should be covered before painting. Paint splashes should be removed immediately with water.
4.  Tools should be washed immediately after use with clean water.

NANO ANTI - MOULD Paint - Important notes
Material, ambient and substrate temperature should be between +5 °C and +30 °C for painting. Drying time: approx. 5 hours at +20 °C and 65% relative humidity. To achieve a uniform finish, always use NANO Anti-Mould Paint from the same batch. Avoid skin and eye contact, wear gloves and protective goggles (not glass).

NANO ANTI - MOULD Paint - Consumption
Depending on the structure and absorbency of the substrate: 150 – 170 ml/m² per coat. If necessary, apply a coat to a test area to determine precise consumption.

NANO ANTI - MOULD Paint - Overpainting
Overpainting after approx. 5 hours.

NANO ANTI - MOULD Paint - Storage
The container should be tightly sealed and kept in a cool but frost-free place. Unopened and properly stored, the product will remain stable for at least 6 months after the date of manufacture.

NANO ANTI - MOULD PAINT Registration for NANO products BAUA (German Federal Institute for Occupational Safety and Health):N-50355

 

NANO ANTI - MOULD Paint - ChemVOCFarbV (Decopaint Directive)

Category                                             A/a

VOC limit value (g/l)                            30 (2010)

Maximum VOC content (g/l)               1

 

Important Note - use NANO ANTI MOULD PAINT with BRÜCOL® MOLD STOP FOAM SPRAY 

 

BRÜCOL® MOLD STOP FOAM SPRAY 750 ml - product features
Spray against  mildew from walls.

Dosage and use:
Spray or paint mold from a short distance. In infected silicone seals, the means can also be applied with a brush. Wash off in the wet area after 1 hour with water.
On masonry, plaster or wallpaper no treatment is required.
Note: Mold Stop don´t attacks coatings, paints, enamels, plastics, glass and tile

physical data:
Physical state:         liquid
color:                      light yellow
odor:                      specifically, faintly of formic acid
pHt:                        2,75
density:                  1,02 g/cm3
solubility in water:  mixable with water

Ingredients according to Biocidal Regulation (EC) - RL 98
10 g/kg hydrogen peroxide
28 g/kg formic acid
Baua-Reg. Nr. N30463

Labelling   GHS07  Warning Hazard statements:
H315 Causes skin irritation
H319 Causes serious eye irritation
Use biocides safely. Always read the label and product information before use.

Made in Germany 

  

Höpner Lacke GmbH - Manufacturer Höpner NANO ANTI - MOULD Paint

Contact: Höpner Lacke GmbH Fabrikstraße 4 | 02906 Niesky  |Fon +49 (0) 3588 20 43 53 | Fax +49 (0) 3588 20 78 95  E-Mail:  info@hoepner-lacke.de